boards/arm/nucleo-f429zi: Add example trace
Add example trace for board nucleo-f429zi Signed-off-by: yangwei-x <yangwei3@lixiang.com>
This commit is contained in:
William Yang
Xiang Xiao
parent
4568110d63
commit
6633f9d907
2 changed files with 300 additions and 0 deletions
|
|
@ -5,3 +5,213 @@ ST Nucleo F429ZI
|
|||
.. tags:: chip:stm32, chip:stm32f4, chip:stm32f429
|
||||
|
||||
The Nucleo F429ZI is a member of the Nucleo-144 board family.
|
||||
|
||||
This page discusses issues unique to NuttX configurations for the ST
|
||||
Nucleo F429ZI board from ST Micro. See
|
||||
|
||||
http://www.st.com/en/evaluation-tools/nucleo-f429zi.html
|
||||
|
||||
NucleoF429ZI:
|
||||
|
||||
- Microprocessor: 32-bit ARM Cortex M4 with 180 MHz max CPU frequency
|
||||
- Memory: 2 MB Flash and 256+4 KB SRAM including 64-Kbyte of core coupled memory
|
||||
- ADC: 3x12-bit ADC with 24 channels
|
||||
- DMA: 16-stream DMA controller with FIFOs and burst support
|
||||
- Timers: Up to 17 timers: up to 12 16-bit, 2 32-bit timers, two
|
||||
watchdog timers, and a SysTick timer
|
||||
- GPIO: Up to 168 I/O ports with interrupt capability
|
||||
- I2C: Up to 3 I2C interfaces
|
||||
- USARTs: Up to 4 USARTs
|
||||
- SPIs: Up to 6 SPIs (45 Mbit/s)
|
||||
|
||||
|
||||
See:
|
||||
https://www.st.com/en/microcontrollers-microprocessors/stm32f429zi.html
|
||||
|
||||
|
||||
Hardware
|
||||
========
|
||||
|
||||
Buttons
|
||||
-------
|
||||
|
||||
B1 USER: the user button is connected to the I/O PC13 (pin 2) of the STM32
|
||||
microcontroller.
|
||||
|
||||
LEDs
|
||||
----
|
||||
|
||||
The Nucleo F410RB provide a single user LED, LD2. LD2
|
||||
is the green LED connected to Arduino signal D13 corresponding to MCU I/O
|
||||
PA5 (pin 21) or PB13 (pin 34) depending on the STM32target.
|
||||
|
||||
- When the I/O is HIGH value, the LED is on.
|
||||
- When the I/O is LOW, the LED is off.
|
||||
|
||||
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
||||
defined. In that case, the usage by the board port is defined in
|
||||
include/board.h and src/sam_leds.c. The LEDs are used to encode OS-related
|
||||
events as follows when the red LED (PE24) is available::
|
||||
|
||||
SYMBOL Meaning LD2
|
||||
------------------- ----------------------- -----------
|
||||
LED_STARTED NuttX has been started OFF
|
||||
LED_HEAPALLOCATE Heap has been allocated OFF
|
||||
LED_IRQSENABLED Interrupts enabled OFF
|
||||
LED_STACKCREATED Idle stack created ON
|
||||
LED_INIRQ In an interrupt No change
|
||||
LED_SIGNAL In a signal handler No change
|
||||
LED_ASSERTION An assertion failed No change
|
||||
LED_PANIC The system has crashed Blinking
|
||||
LED_IDLE MCU is is sleep mode Not used
|
||||
|
||||
Thus if LD2, NuttX has successfully booted and is, apparently, running
|
||||
normally. If LD2 is flashing at approximately 2Hz, then a fatal error
|
||||
has been detected and the system has halted.
|
||||
|
||||
Serial Consoles
|
||||
===============
|
||||
|
||||
USART1
|
||||
------
|
||||
|
||||
Pins and Connectors::
|
||||
|
||||
RXD: PA11 CN10 pin 14
|
||||
PB7 CN7 pin 21
|
||||
TXD: PA10 CN9 pin 3, CN10 pin 33
|
||||
PB6 CN5 pin 3, CN10 pin 17
|
||||
|
||||
NOTE: You may need to edit the include/board.h to select different USART1
|
||||
pin selections.
|
||||
|
||||
TTL to RS-232 converter connection::
|
||||
|
||||
Nucleo CN10 STM32F429ZI
|
||||
----------- ------------
|
||||
Pin 21 PA9 USART1_RX *Warning you make need to reverse RX/TX on
|
||||
Pin 33 PA10 USART1_TX some RS-232 converters
|
||||
Pin 20 GND
|
||||
Pin 8 U5V
|
||||
|
||||
To configure USART1 as the console::
|
||||
|
||||
CONFIG_STM32_USART1=y
|
||||
CONFIG_USART1_SERIALDRIVER=y
|
||||
CONFIG_USART1_SERIAL_CONSOLE=y
|
||||
CONFIG_USART1_RXBUFSIZE=256
|
||||
CONFIG_USART1_TXBUFSIZE=256
|
||||
CONFIG_USART1_BAUD=115200
|
||||
CONFIG_USART1_BITS=8
|
||||
CONFIG_USART1_PARITY=0
|
||||
CONFIG_USART1_2STOP=0
|
||||
|
||||
USART2
|
||||
------
|
||||
|
||||
Pins and Connectors::
|
||||
|
||||
RXD: PA3 CN9 pin 1 (See SB13, 14, 62, 63). CN10 pin 37
|
||||
PD6
|
||||
TXD: PA2 CN9 pin 2(See SB13, 14, 62, 63). CN10 pin 35
|
||||
PD5
|
||||
|
||||
UART2 is the default in all of these configurations.
|
||||
|
||||
TTL to RS-232 converter connection::
|
||||
|
||||
Nucleo CN9 STM32F429ZI
|
||||
----------- ------------
|
||||
Pin 1 PA3 USART2_RX *Warning you make need to reverse RX/TX on
|
||||
Pin 2 PA2 USART2_TX some RS-232 converters
|
||||
|
||||
Solder Bridges. This configuration requires:
|
||||
|
||||
- SB62 and SB63 Closed: PA2 and PA3 on STM32 MCU are connected to D1 and D0
|
||||
(pin 7 and pin 8) on Arduino connector CN9 and ST Morpho connector CN10
|
||||
as USART signals. Thus SB13 and SB14 should be OFF.
|
||||
|
||||
- SB13 and SB14 Open: PA2 and PA3 on STM32F103C8T6 (ST-LINK MCU) are
|
||||
disconnected to PA3 and PA2 on STM32 MCU.
|
||||
|
||||
To configure USART2 as the console::
|
||||
|
||||
CONFIG_STM32_USART2=y
|
||||
CONFIG_USART2_SERIALDRIVER=y
|
||||
CONFIG_USART2_SERIAL_CONSOLE=y
|
||||
CONFIG_USART2_RXBUFSIZE=256
|
||||
CONFIG_USART2_TXBUFSIZE=256
|
||||
CONFIG_USART2_BAUD=115200
|
||||
CONFIG_USART2_BITS=8
|
||||
CONFIG_USART2_PARITY=0
|
||||
CONFIG_USART2_2STOP=0
|
||||
|
||||
USART6
|
||||
------
|
||||
|
||||
Pins and Connectors::
|
||||
|
||||
RXD: PC7 CN5 pin2, CN10 pin 19
|
||||
PA12 CN10, pin 12
|
||||
TXD: PC6 CN10, pin 4
|
||||
PA11 CN10, pin 14
|
||||
|
||||
To configure USART6 as the console::
|
||||
|
||||
CONFIG_STM32_USART6=y
|
||||
CONFIG_USART6_SERIALDRIVER=y
|
||||
CONFIG_USART6_SERIAL_CONSOLE=y
|
||||
CONFIG_USART6_RXBUFSIZE=256
|
||||
CONFIG_USART6_TXBUFSIZE=256
|
||||
CONFIG_USART6_BAUD=115200
|
||||
CONFIG_USART6_BITS=8
|
||||
CONFIG_USART6_PARITY=0
|
||||
CONFIG_USART6_2STOP=0
|
||||
|
||||
Virtual COM Port
|
||||
----------------
|
||||
|
||||
Yet another option is to use UART2 and the USB virtual COM port. This
|
||||
option may be more convenient for long term development, but is painful
|
||||
to use during board bring-up.
|
||||
|
||||
Solder Bridges. This configuration requires:
|
||||
|
||||
- SB62 and SB63 Open: PA2 and PA3 on STM32 MCU are disconnected to D1
|
||||
and D0 (pin 7 and pin 8) on Arduino connector CN9 and ST Morpho
|
||||
connector CN10.
|
||||
|
||||
- SB13 and SB14 Closed: PA2 and PA3 on STM32F103C8T6 (ST-LINK MCU) are
|
||||
connected to PA3 and PA2 on STM32 MCU to have USART communication
|
||||
between them. Thus SB61, SB62 and SB63 should be OFF.
|
||||
|
||||
Configuring USART2 is the same as given above.
|
||||
|
||||
Question: What BAUD should be configure to interface with the Virtual
|
||||
COM port? 115200 8N1?
|
||||
|
||||
Default:
|
||||
As shipped, SB62 and SB63 are open and SB13 and SB14 closed, so the
|
||||
virtual COM port is enabled.
|
||||
|
||||
Configurations
|
||||
==============
|
||||
|
||||
trace
|
||||
---
|
||||
|
||||
Configures the trace located at apps/system/trace for the
|
||||
Nucleo-F429ZI board. The Configuration enables the serial interfaces
|
||||
on UART2. Support for builtin applications is enabled, and selected
|
||||
application trace.
|
||||
|
||||
NOTES:
|
||||
|
||||
1. This configuration uses the mconf-based configuration tool. To
|
||||
change this configuration using that tool, you should:
|
||||
|
||||
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
||||
see additional README.txt files in the NuttX tools repository.
|
||||
|
||||
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
||||
reconfiguration process.
|
||||
|
|
|
|||
90
boards/arm/stm32/nucleo-f429zi/configs/trace/defconfig
Normal file
90
boards/arm/stm32/nucleo-f429zi/configs/trace/defconfig
Normal file
|
|
@ -0,0 +1,90 @@
|
|||
#
|
||||
# This file is autogenerated: PLEASE DO NOT EDIT IT.
|
||||
#
|
||||
# You can use "make menuconfig" to make any modifications to the installed .config file.
|
||||
# You can then do "make savedefconfig" to generate a new defconfig file that includes your
|
||||
# modifications.
|
||||
#
|
||||
# CONFIG_ARCH_FPU is not set
|
||||
# CONFIG_STM32_FLASH_PREFETCH is not set
|
||||
# CONFIG_STM32_USE_LEGACY_PINMAP is not set
|
||||
CONFIG_ARCH="arm"
|
||||
CONFIG_ARCH_BOARD="nucleo-f429zi"
|
||||
CONFIG_ARCH_BOARD_NUCLEO_F429ZI=y
|
||||
CONFIG_ARCH_BUTTONS=y
|
||||
CONFIG_ARCH_CHIP="stm32"
|
||||
CONFIG_ARCH_CHIP_STM32=y
|
||||
CONFIG_ARCH_CHIP_STM32F429Z=y
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_BOARD_LOOPSPERMSEC=16717
|
||||
CONFIG_BUILTIN=y
|
||||
CONFIG_DEBUG_SYMBOLS=y
|
||||
CONFIG_DRIVERS_NOTE=y
|
||||
CONFIG_DRIVERS_NOTECTL=y
|
||||
CONFIG_ETH0_PHY_LAN8742A=y
|
||||
CONFIG_FS_PROCFS=y
|
||||
CONFIG_FS_PROCFS_REGISTER=y
|
||||
CONFIG_FS_TMPFS=y
|
||||
CONFIG_HAVE_CXX=y
|
||||
CONFIG_HAVE_CXXINITIALIZE=y
|
||||
CONFIG_INIT_ENTRYPOINT="nsh_main"
|
||||
CONFIG_INTELHEX_BINARY=y
|
||||
CONFIG_LINE_MAX=64
|
||||
CONFIG_MM_REGIONS=2
|
||||
CONFIG_NET=y
|
||||
CONFIG_NETDB_DNSCLIENT=y
|
||||
CONFIG_NETINIT_DHCPC=y
|
||||
CONFIG_NETINIT_NOMAC=y
|
||||
CONFIG_NETUTILS_DISCOVER=y
|
||||
CONFIG_NETUTILS_TELNETD=y
|
||||
CONFIG_NETUTILS_WEBCLIENT=y
|
||||
CONFIG_NET_ARP_IPIN=y
|
||||
CONFIG_NET_BROADCAST=y
|
||||
CONFIG_NET_ETH_PKTSIZE=1500
|
||||
CONFIG_NET_ICMP_SOCKET=y
|
||||
CONFIG_NET_IGMP=y
|
||||
CONFIG_NET_LOOPBACK=y
|
||||
CONFIG_NET_ROUTE=y
|
||||
CONFIG_NET_STATISTICS=y
|
||||
CONFIG_NET_TCP=y
|
||||
CONFIG_NET_UDP=y
|
||||
CONFIG_NET_UDP_CHECKSUMS=y
|
||||
CONFIG_NSH_BUILTIN_APPS=y
|
||||
CONFIG_NSH_FILEIOSIZE=512
|
||||
CONFIG_NSH_READLINE=y
|
||||
CONFIG_NUCLEO_F429ZI_CONSOLE_VIRTUAL=y
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
CONFIG_RAM_SIZE=114688
|
||||
CONFIG_RAM_START=0x20000000
|
||||
CONFIG_RAW_BINARY=y
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_SCHED_HPWORK=y
|
||||
CONFIG_SCHED_INSTRUMENTATION=y
|
||||
CONFIG_SCHED_INSTRUMENTATION_DUMP=y
|
||||
CONFIG_SCHED_INSTRUMENTATION_FILTER=y
|
||||
CONFIG_SCHED_LPWORK=y
|
||||
CONFIG_SCHED_WAITPID=y
|
||||
CONFIG_SPI=y
|
||||
CONFIG_STACK_USAGE=y
|
||||
CONFIG_START_DAY=6
|
||||
CONFIG_START_MONTH=12
|
||||
CONFIG_START_YEAR=2011
|
||||
CONFIG_STM32_DISABLE_IDLE_SLEEP_DURING_DEBUG=y
|
||||
CONFIG_STM32_ETHMAC=y
|
||||
CONFIG_STM32_FLASH_CONFIG_I=y
|
||||
CONFIG_STM32_PHYADDR=0
|
||||
CONFIG_STM32_PHYSR=31
|
||||
CONFIG_STM32_PHYSR_100FD=0x0018
|
||||
CONFIG_STM32_PHYSR_100HD=0x0008
|
||||
CONFIG_STM32_PHYSR_10FD=0x0014
|
||||
CONFIG_STM32_PHYSR_10HD=0x0004
|
||||
CONFIG_STM32_PHYSR_ALTCONFIG=y
|
||||
CONFIG_STM32_PHYSR_ALTMODE=0x001c
|
||||
CONFIG_STM32_RMII_EXTCLK=y
|
||||
CONFIG_SYSTEM_DHCPC_RENEW=y
|
||||
CONFIG_SYSTEM_NSH=y
|
||||
CONFIG_SYSTEM_PING=y
|
||||
CONFIG_SYSTEM_TRACE=y
|
||||
CONFIG_SYSTEM_TRACE_STACKSIZE=8192
|
||||
CONFIG_TASK_NAME_SIZE=32
|
||||
CONFIG_USART3_SERIAL_CONSOLE=y
|
||||
Loading…
Add table
Reference in a new issue