This updated the command used for running the openocd-esp32 for
all the supported Espressif's SoCs. It enables using SW-defined
breakpoints.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
Change the ESP32S3-WROOM-2-N16R8V to ESP32S3-WROOM-1-N8R2.
Reason: not testing on 16MB but successfully tested smaller flash and PSRAM.
Also updated documentation on this defconfig.
Signed-off-by: Filipe Cavalcanti <filipe.cavalcanti@espressif.com>
Modify addressing to allow only 2 byte node address.
Allow modifying the node address by modifying the ipv6 address
(the ipv6 address has a direct relation with the node address)
Introduce the option to add a 4 byte random number to the mac header
as a preparation for ciphered data exchange.
Introduce a FCB (frame control byte) as a replacement for the INFO
field in the mac header.
Update esp32-devkitc:espnow config to reflect address size change.
Update the documentation to reflect address size changes.
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Now, espressif qemu supports MCUboot, so we can switch the app
format.
The build was failing with the legacy app format because
_ext_ram_bss_end and _ext_ram_bss_start are not defined in the
legacy linker file.
Added documentation for espnow and a default defconfig to illustrate
the use of espnow for udp communication.
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Stack and backtrace dump for Espressif's SoCs (ESP32, ESP32-S2,
ESP32-S3, ESP32-C3, ESP32-C6 and ESP32-H2) is now documented in a
new section for each chip entry page.
boards/xtensa/esp32s3/esp32s3-devkit|esp32s3-korvo-2/configs/sdmmc/defconfig: defconfig for sdmmc support
Add description for sdmmc support on esp32s3 in the board specific documentation.
Add defconfig for esp32s3-devkit with external adapter and emmc module.
Add defconfig for esp32s3-korvo-2 with SD slot enabled.
Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
arch/xtensa/src/esp32s3/hardware/esp32s3_sdmmc.h|esp32s3_soc.h,
boards/xtensa/esp32s3/common/include/esp32s3_board_sdmmc.h,
boards/xtensa/esp32s3/common/src/Make.defs|esp32s3_board_sdmmc.c,
boards/xtensa/esp32s3/esp32s3-devkit/src/esp32s3_bringup.c: add SD/mmc driver
Support 1-bit bus width and 4-bit bus width. Support eMMC high speed SDR mode.
Support transfer data with DMA. Support SD clock frequency up to 40MHZ.
Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
The ESP32-S3-Korvo-2 is a multimedia development board based on the
ESP32-S3 chip. It is equipped with a two-microphone array which is
suitable for voice recognition and near/far-field voice wake-up
applications. The board integrates multiple peripherals such as
LCD, camera, and microSD card. It also supports JPEG video stream
processing. With all of its outstanding features, the board is an
ideal choice for the development of low-cost and low-power
network-connected audio and video products.
Provide `up_copy_section` function that enables copying data using
the data bus. If the memory destination address is accessible
through the instruction bus, the data is copied using the
correspondent address accessible through the data bus.
arch/xtensa: add support for capture driver on ESP32 and ESP32|S3|
Squashed:
Initial settings for MCPWM Capture on board level
Created lower half files - compilation ok
Using capture debug features. Simple example on fops works
Successful duty and freq calculation
Documentation update
Fixed and added interupt capabilities for all 3 capture channels
Cleaned defconfig
Renamed macros, added S3 options and moved arch source to common dir
Added support for ESP32S3
Added capture example to defconfig and renamed
Basic bring up ready. New Kconfig options for motor.
Good motor registration
Working on enabling pwm generators
Working on enabling pwm generators
Added fops functions
Success on PWM 50%
stable pwm operation for bdc
Added loopback option for testing
Improved rules on fsm
Working motor direction control
Testing new ISR for fault handling
Issues on fault ISR
Removed fault implementation (not working)
Added support for esp32s3
Documentation improvements
Added default motor spin direction
Added parameter change while running
Review fixes
arch/xtensa: add support for fault signal on motor control
Squashed:
Initial settings for MCPWM Capture on board level
Created lower half files - compilation ok
Using capture debug features. Simple example on fops works
Successful duty and freq calculation
Documentation update
Fixed and added interupt capabilities for all 3 capture channels
Cleaned defconfig
Renamed macros, added S3 options and moved arch source to common dir
Added support for ESP32S3
Added capture example to defconfig and renamed
Basic bring up ready. New Kconfig options for motor.
Good motor registration
Working on enabling pwm generators
Working on enabling pwm generators
Added fops functions
Success on PWM 50%
stable pwm operation for bdc
Added loopback option for testing
Improved rules on fsm
Working motor direction control
Testing new ISR for fault handling
Issues on fault ISR
Removed fault implementation (not working)
Added support for esp32s3
Documentation improvements
Added default motor spin direction
Added parameter change while running
Got responsive fault indicator
Working brakes - still need to work on starting isr
Fixed single-time ISR initializiation
Working soft brake on fault
Improved KConfig for BDC and BLDC
Kconfig fixed at board level
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.
This commit also removes deprecated code and makes this bootloader
configuration as default for esp32 targets and removes the need
for running 'make bootloader' command for it.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
Squashed:
Initial settings for MCPWM Capture on board level
Created lower half files - compilation ok
Using capture debug features. Simple example on fops works
Successful duty and freq calculation
Documentation update
Fixed and added interupt capabilities for all 3 capture channels
Cleaned defconfig
Renamed macros, added S3 options and moved arch source to common dir
Added support for ESP32S3
Added capture example to defconfig and renamed
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.
This commit also removes deprecated code and makes this bootloader
configuration as default for esp32s2 targets and removes the need
for running 'make bootloader' command for it.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
