75d0c2946d
The code is mainly derived from the NuttX qemu-rv/rv-virt codebase.
Major changes:
- boards/Kconfig: add new BOARD_K230_CANMV
- arch/risc-v/Kconfig: add new CHIP_K230 chip and ARCH_RV_MMIO_BITS
- arch/risc-v/src/common/riscv_mtimer.c: use ARCH_RV_MMIO_BITS to
select MMIO access width
New additions:
- arch/risc-v/include/k230/: k230 SoC definitions
- arch/risc-v/src/k230/: k230 SoC sources
- boards/risc-v/k230/canmv230/: CanMV-K230 board sources and configs
- Documentation/platforms/risc-v/k230/: simple doc
Note that only FLAT build works for canmv230 now.
This PR has changes in RiscV common layer thus may affect other RiscV ports
It changes the mtime/mtimecmp access control from using config ARCH_RV64 to
newly intorduced config ARCH_RV_MMIO_BITS.
Original design uses ARCH_RV64 to select 64bit MMIO in riscv_mtimer.c, this
can't cope with the situation with K230 --- it has ARCH_RV64 but only can do
32bit MMIO. So a new ARCH_RV_MMIO_BITS config has been introduced. Its value
depicts the MMIO width in bits. The MMIO_BITS defaults to 32/64 for RV32/
RV64 respectively. This allows the macro to replace current use of ARCH_RV64
in riscv_mtimer.c.
The new MMIO_BITS config is a derived one, and for RiscV chips with
equal CPU and MMIO widths there is no need to explicitly set it as the
default rule will do that. Only chips with different CPU and MMIO widths
need set it in Kconfig.
So by design this change should be safe but RiscV ports should be checked.
"ostest" verification has been done for:
- canmv230/nsh
- rv-vivt/nsh
- rv-virt/nsh64
configuration generation and manual check of derived RV_MMIO_BITS has been
done for:
- star64/nsh
- arty_a7/nsh
- bl602evb/nsh
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
|
||
|---|---|---|
| .github | ||
| arch | ||
| audio | ||
| binfmt | ||
| boards | ||
| cmake | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| dummy | ||
| fs | ||
| graphics | ||
| include | ||
| libs | ||
| mm | ||
| net | ||
| openamp | ||
| pass1 | ||
| sched | ||
| syscall | ||
| tools | ||
| video | ||
| wireless | ||
| .asf.yaml | ||
| .gitignore | ||
| .yamllint | ||
| AUTHORS | ||
| CMakeLists.txt | ||
| CONTRIBUTING.md | ||
| INVIOLABLES.md | ||
| Kconfig | ||
| LICENSE | ||
| Makefile | ||
| NOTICE | ||
| README.md | ||
| ReleaseNotes | ||
Apache NuttX is a real-time operating system (RTOS) with an emphasis on standards compliance and small footprint. Scalable from 8-bit to 64-bit microcontroller environments, the primary governing standards in NuttX are POSIX and ANSI standards. Additional standard APIs from Unix and other common RTOSs (such as VxWorks) are adopted for functionality not available under these standards, or for functionality that is not appropriate for deeply-embedded environments (such as fork()).
For brevity, many parts of the documentation will refer to Apache NuttX as simply NuttX.
Getting Started
First time on NuttX? Read the Getting Started guide! If you don't have a board available, NuttX has its own simulator that you can run on terminal.
Documentation
You can find the current NuttX documentation on the Documentation Page.
Alternatively, you can build the documentation yourself by following the Documentation Build Instructions.
The old NuttX documentation is still available in the Apache wiki.
Supported Boards
NuttX supports a wide variety of platforms. See the full list on the Supported Platforms page.
Contributing
If you wish to contribute to the NuttX project, read the Contributing guidelines for information on Git usage, coding standard, workflow and the NuttX principles.
License
The code in this repository is under either the Apache 2 license, or a license compatible with the Apache 2 license. See the License Page for more information.