Gregory Nutt 391367e8ca LPC17 Ethernet: Add support for the Micrel KSZ8041 PHY.		2015-06-03 17:34:36 -06:00
..
arp.h	Standardize some header files	2015-02-16 14:29:43 -06:00
cs89x0.h	Standardize some header files	2015-02-16 14:29:43 -06:00
enc28j60.h	Standardize some header files	2015-02-16 14:29:43 -06:00
encx24j600.h	Add ENCX24J600 Ethernet driver and support for the ENCX24J600 with the Olimex STM32 P107 board. From Max Holtberg	2013-08-25 11:21:54 -06:00
ethernet.h	Standardize some header files	2015-02-16 14:29:43 -06:00
gmii.h	Standardize some header files	2015-02-16 14:29:43 -06:00
icmp.h	Networking: Replace all references to net_ipaddr_t with either in_addr_t on net_ipv6addr_t. The goal is to support both IPv4 and IPv6 simultaneously. This requires that the two types be distinct and not conditionally typedef'ed to net_ipaddr_t.	2015-01-16 12:30:18 -06:00
icmpv6.h	Networking: Add support for sending ICMPv6 Router Solicitation and receiving Router advertisement. This is a part of the ICMPv6 auto-configuration logic is still still not complete	2015-02-03 13:25:28 -06:00
igmp.h	Networking: Misck IPv6 detanglement	2015-01-15 12:19:44 -06:00
iob.h	Networking: The are issues with the TCP write-ahead buffering if CONFIG_NET_NOINTS is enabled: There is a possibility of deadlocks in certain timing conditions. I have not seen this with the Tiva driver that I have been users but other people claim to see the issue on other platforms. Certainly it is a logic error: The network should never wait for TCP read-ahead buffering space to be available. It should drop the packets immediately.	2015-01-27 21:23:42 -06:00
ioctl.h	Add an ioctal() that can be used to perform ICMPv6 auto-configuration	2015-02-03 08:54:42 -06:00
ip.h	Networking: Get rid of g_ipv4_allzeroaddr and g_ipv4_alloneaddr. It is more efficient and more intuitive to use INADDR_ANY and INADDR_BROADCAST	2015-05-29 15:16:11 -06:00
ipopt.h	NET: rename include/net/ip.h to ipopt.h	2014-07-04 16:44:53 -06:00
mii.h	LPC17 Ethernet: Add support for the Micrel KSZ8041 PHY.	2015-06-03 17:34:36 -06:00
net.h	Networking: The network device list was protected by a re-entrant semaphore. With the recent change to support network device callback, the network stack needs to access the network device list too. Some drivers, however, run the network stack from the interrupt level -- this is bad but a fact in the current state. Of course,those drivers are unable to take the semaphore and will assert.	2015-05-31 08:34:03 -06:00
netconfig.h	Adjust microMIPS compile options to enable interlinking with 32-bit code	2015-02-25 09:54:48 -06:00
netdev.h	Networking: Modify event list handling: Now there are two event lists each device structure: (1) One is for ARP and ICMP data related evetns, the other is for device related events. Callback allocation/free routines no accept a device paramter as well as a list: If the device paramter is added, then the callback goes into both the connection-related liast AND the device event list. Thus each socket type can received both custom data-related events as well as common device related events.	2015-05-28 12:01:38 -06:00
netstats.h	Networking: Clean up network status collection and presentation for IPv6	2015-01-24 08:26:12 -06:00
phy.h	Finishes the ioctl definition to subscribe to PHY events. Revamp network ioctl signature to support arguments other than struct mii_ioctl_data.	2014-08-16 14:08:04 -06:00
pkt.h	NET: Most of the contents of include/nuttx/net/pkt.h moved to net/pkt/pkt.h	2014-07-05 13:59:22 -06:00
slip.h	Move SLIP prototypes from net.h to new slip.h	2014-08-16 10:28:45 -06:00
tcp.h	Networking: Final detangle off IPv4 and IPv6 TCP/UDP send logic. The Networking subsystem now compiles with IPv6 enabled	2015-01-18 08:56:05 -06:00
tun.h	Add TUN device. From Max Neklyudov	2015-03-11 06:52:56 -06:00
udp.h	Networking: Final detangle off IPv4 and IPv6 TCP/UDP send logic. The Networking subsystem now compiles with IPv6 enabled	2015-01-18 08:56:05 -06:00