This commit implements simple (blocking) read and write operations
for the i2schar driver. Although it already contained such methods,
the read/write operation was not being properly handled by the
`i2schar_[rx|tx]callback` (called when the operation has finished).
A semaphore is used to ensure that read data was received by the
receiver and another semaphore ensures that data was written by the
transmitter.
Please note that the already-existing mutex for the I2S peripheral
was replaced by two mutexes, one for the receiver and other for the
transmitter to allow full-duplex communication.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
This commit implements a set of commands to the i2s character
driver. The implemented commands allows getting and setting
parameters like data width, sample rate and number of channels for
both receiver and transmitter. If no ioctl is found, the command
is redirected to the lower driver implementation if it has the
ioctl callback registered.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
Instead of verifying MMD indirect access by checking
EEE ADVERTISEMENT register has value 0x6 (which may be changed),
the verification is done by write and check LED MODE register.
1. Backup current LED_MODE register value
2. Write value Single-LED mode (0x10) to LED_MODE
3. Read LED_MODE register and verify it returns value 0x10
4. Write original (backup) value to LED_MODE
From the ksz9477 errata, setup the configuration which is tested to work.
- Improve PHY receive performance
- Disable EEE for ports 1-5
- Fix supply current values
Signed-off-by: Jani Paalijarvi <jani.paalijarvi@unikie.com>
- Added new part support for PCAL6416
- Added pullup/pulldown configuration support
Signed-off-by: Jouni Ukkonen <jouni.ukkonen@unikie.com>
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
- Fix gpioinfo argument type
- Fix unused variable "ret" warning when CONFIG_TCA64XX_INT_POLL is not defined
Signed-off-by: Jouni Ukkonen <jouni.ukkonen@unikie.com>
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
This commit removes existing support for the NCV7410 10BASE-T1S MAC-PHY.
The driver will be replaced by its generalized version with different organization.
The new driver has naming clashes with the old, therefore the old has to be removed first.
Signed-off-by: michal matias <mich4l.matias@gmail.com>
Configure number of passes in interrupt handler logic to avoid losing RX frames
in QEMU environment.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
Add support for the Texas Instruments TMP112 I2C/SMBus digital
temperature sensor. Also add a new defconfig that includes
support for a TMP112 sensor and extend the existing documentation
to include its description.
Signed-off-by: Niccolò Maggioni <nicco.maggioni+nuttx@gmail.com>
This patch fixes an incorrect call to stm32_cap_initialize() in
stm32_bringup.c: the call was made without the channel parameter.
Instead of adding the channel in the call, the channel is selected by
stm32_cap_gpio() (first available channel).
This patch also fixes incorrect driver registration in
drivers/timers/capture.c: the driver was registered with the wrong
name (/dev/cap -> /dev/capture). Also added more error checking in
cap_register_multiple().
Signed-off-by: Côme VINCENT <44554692+comejv@users.noreply.github.com>
Fix mutex locking bugs and improve performance. Fix interval no longer
set statically since it is available via `set_interval` uORB function.
Activation/deactivation no longer triggers standby/hotstart since this
functionality was very unstable.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
This commit introduces a timer capture driver for the STM32H7 series
ported from the STM32 F series.
The main changes include:
- A new generic timer capture driver for STM32H7.
- A lower-half driver to integrate with the NuttX capture subsystem.
- Kconfig options to enable and configure capture for various timers.
- Pin definitions for TIM1-4 capture inputs on the nucleo-h743zi.
- An update to `cap_register_multiple` to handle multiple device registration.
- An update to `stm32_bringup` to register the capture drivers.
The current implementation is based on a driver originally for PWM input,
and as such, it calculates duty cycle and frequency. It is also limited
to a single capture channel per timer.
The original implementation's `stm32_cap_init` in
`arch/arm/src/stm32h7/stm32_capture.c` has been modified to accept a
channel number instead of using a hardcoded 0 through
`STM32_CAP_CHANNEL_COUNTER`.
This serves as a foundation for future development of more comprehensive
input capture capabilities on STM32H7 platforms.
Tested by polling and reading `/dev/cap0-4` with
`ioctl(fds[i], CAPIOC_FREQUENCE, freq)` while sending a square wave signal to
appropriate pins and checking frequency.
Also tested by bypassing upper half driver and setting up capture on
TIM4 channels 1-4 as explained in #16762.
Signed-off-by: Côme VINCENT <44554692+comejv@users.noreply.github.com>
This commit simplifies sending errors back to OP-TEE and avoids
code duplication when handling errno values.
Signed-off-by: Theodore Karatapanis <tkaratapanis@census-labs.com>
This commit expands RPC support for the OP-TEE driver using 2 files:
1) drivers/misc/optee_rpc.c
* Add support for RPCs that can be handled directly by the kernel.
* Can delegate RPC handling to optee_supplicant.c for RPCs that
need userspace interaction.
2) drivers/misc/optee_supplicant.c
* Enable communication between the userspace TEE supplicant and the
kernel driver.
Additional changes were needed to the following files:
1) drivers/misc/optee.c
* Add ioctls used SOLELY by the userspace TEE supplicant.
* Register /dev/teepriv0 if the supplicant is enabled in Kconfig
* Add OPTEE_ROLE_CA and OPTEE_ROLE_SUPPLICANT conditionals to
differentiate paths, between a normal Client Application (CA)
and the TEE supplicant.
* Change some functions from static to "public" to reuse them
in other C files.
* Adjust optee_to/from_msg_param() to work with RPCs.
2) drivers/misc/optee_smc.c
* Call the RPC handler from optee_rpc.c
3) drivers/misc/optee_msg.h
* Add definition needed for RPCs
4) drivers/misc/tee.h
* Add ioctl definitions
* Add TEE_SHM_SUPP flag, checked when unregistering supplicant
memory.
5) Documentation/guides/optee.rs
* Add documentation for RPCs and the supplicant.
6) drivers/misc/{CMakeLists.txt, Make.defs}
* Account for the new files.
7) drivers/misc/Kconfig
* Add DEV_OPTEE_SUPPLICANT option to enable/disable the supplicant
driver.
Signed-off-by: Theodore Karatapanis <tkaratapanis@census-labs.com>
The previous approach with memfd has 3 problems:
1) The close operation on the memfd isn't tied with optee_shm_close,
therefore close(fd) doesn't free the optee_shm struct allocated
by the kernel.
2) The kernel unnecessarily maps the file descriptor to its memory,
however only userspace should need to do that.
3) Since the kernel doesn't need to map the file descriptor we
don't need to unmap it.
To use anonymous mapping, the prototype of map_anonymous() was
moved from fs/mmap/fs_anonmap.h to include/nuttx/fs/fs.h. Since
fs_anonmap.h didn't contain any other information it is deleted.
A type from fs/mmap/fs_rammap.h was moved to the public :
include/nuttx/fs/fs.h as well.
Signed-off-by: Theodore Karatapanis <tkaratapanis@census-labs.com>
The VA -> PA translation must be performed once, at allocation time,
while the caller's virtual address space is known. If a second process
later tries to translate the same VA from a different mapping, the
calculated physical address can be wrong.
Signed-off-by: Theodore Karatapanis <tkaratapanis@census-labs.com>
NVBLK provides a block device that operates on top of a non volatile
memory (as a mtd device) that enables wear levelling for non volatile
memory. It's operation is similar to the dhara wear levelling library,
but nvblk is meant to be used on smaller (nor, mram, rram) memory.
I am also the author and maintainer of the nvblk library.
A block device can be created during startup by using:
```
nvblk_initialize(0, mtd, CONFIG_MTD_NVBLK_DEFAULT_LBS,
CONFIG_MTD_NVBLK_DEFAULT_IOBS,
CONFIG_MTD_NVBLK_DEFAULT_SPEB);
```
and a fat filesystem on top of this as:
```
nsh> mkfatfs /dev/mtdblock0
nsh> mount -t vfat /dev/mtdblock0 /mnt
```
this fat filesystem can then be used:
```
nsh> echo "test" > /mnt/test.txt
nsh> cat test.txt
test
nsh>
```
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Previous change that introduced yielding upon OP-TEE
return with reason foreign interrupt, omitted to include
<sched.h>. This worked on kernel builds, but not on flat
builds. Include it.
Signed-off-by: George Poulios <gpoulios@census-labs.com>
CPU heavy OP-TEE calls would starve the Normal World tasks.
OP-TEE foreign interrupts were delivered to NW but we would
resume OP-TEE immediately without giving any potentially
unblocked tasks a chance to run. This would violate real-
time guarantees. Fix that by calling sched_yield() during
OP-TEE return with reason foreign interrupts.
Signed-off-by: George Poulios <gpoulios@census-labs.com>
fb_notify_vsync is called when TE irq comming, and fb_remove_paninfo is called after paninfo comsumed
Signed-off-by: jianglianfang <jianglianfang@xiaomi.com>
Changes the implementation of the L86xxx driver to use the
gnss_lowerhalf driver implementation, simplifying this driver's logic.
It also fixes the `read_line` function which would early return on `\r`,
as well as adding some retries for response checking and better mutex
locking.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
Sometimes this driver will boot when the serial port is of the wrong
baud rate, and it cannot set the correct baud rate or verify
communication. This commit prevents registration if any settings fail to
be set, and also prevents the kernel thread from setting the L86 to
enabled (this is done only by the uORB upper half).
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
update:
CMakeLists.txt
Make.defs
Kconfig
It allows the same version of SystemView target sources to be used for CMake and Make, to avoid discrepancies in the future.
Signed-off-by: simbit18 <simbit18@gmail.com>
According to a reference manual, VCC and VDD undervoltage
and VDD burst leads to the reset of all registers.
Therefore we have to reconfigure the expander to make
it functional again.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
When the MMU is disabled (CONFIG_ARCH_USE_MMU=n) the
data passed back and forth with the TEE needs to be
synced from/to the cache, otherwise we get random data
in either world.
Fix this by cleaning before a call and invalidating after.
This has to be done both on the optee msg arg, and the shm
buffers therein. Cleaning and invalidating the page list
used to describe non-contiguous shm buffers did not seem
mandatory in my tests, but common sense says that it should
be, so we do that too.
This fix does not apply to the optee msg arg of the socket
transport (optee_socket.c), as that one _should_ be handled
by the socket send/recv methods. It does apply to all shm
buffers though, regardless of transport.
Signed-off-by: George Poulios <gpoulios@census-labs.com>
To save more space (equivalent to the size of one erase sector of
MTD device) and to achieve faster read and write speeds, a method
for direct writing was introduced at the FTL layer.
This can be accomplished simply by using the following oflags during
the open operation:
1. O_DIRECT. when this flag is passed in, ftl internally uses
the direct write strategy and no read cache is used in ftl;
otherwise, each write will be executed with the minimum
granularity of flash erase sector size which means a
"sector read back - erase sector - write sector" operation
is performed by using a read cache buffer in heap.
2. O_SYNC. When this flag is passed in, we assume that the
flash has been erased in advance and no erasure operation
will be performed internally within ftl. O_SYNC will take
effect only when both O_DIRECT and O_SYNC are passed in
simultaneously.
3. For uniformity, we remapped the mount flag in mount.h and
unified it with the open flag in fcntl.h. The repetitive
parts of their definitions were reused, and the remaining
part of the mount flag redefine to the unused bit of open
flags.
Signed-off-by: jingfei <jingfei@xiaomi.com>
This reverts commit 20fcdcf905f279a9c4527be399a90590f458db1f.
The reason is that the erase buffer isn't always used in most cases.
Signed-off-by: jingfei <jingfei@xiaomi.com>
This commit creates a sbutton device that uses a single button to
create a keyboard driver that returns TAB or ENTER depending how
long the user keeps the button pressed.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
Since the ADS1115 has a relative slow conversion rate, this additional
ioctl command makes it possible to trigger a conversion before reading
the reading the conversion result, allowing the user to perform other
computation in between instead of waiting for the conversion time to
complete. It improves sampling time.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
